replacing clutch

mars · Sun Oct 21, 2007 1:32 am

ok so i'm going to pick up the clutch/flywheel from steve on monday.... my car cant drive for shit now that the clutch is like 90% dead, slip, outcold!!! so can anyone give me any suggestions on how to do a clutch change?? what tools do i need, and how long is the install gonna take??

THANX IN ADVANCE!!!

mars · Sun Oct 21, 2007 1:33 am

oh also a helping hand would be AWESOME!!!

Sun Oct 21, 2007 7:55 am

Sorry I haven't had a chance to e-mail ya back.

It's pretty simple. You will need to buy or build an engine brace (to hold the engine in place, since you have to remove two of the motor mounts).

Otherwise, just jack the car up. pull the hubs (with brakes still in tact), off of the struts and pull them aside. You will need to remove the big axel nut to do this. (Do this on both sides).

Pull your axles out.

Remove rear motor mount.

Remove passenger, tranny mount (also take the mount 'base' off).

Back out the subframe bolts, so you can hang the subframe down a bit for clearance.

Take your shifter cables off.

Unplug any wire harness's that go to the tranny.

Unbolt all the bell housing bolts (I always put mine in cardboard, so I remember where they went and which way they went...)

Pull the tranny off and out.

It's really not to bad. I'd say it'll probably take a good 4-5 hours to get it out (seeing how its your first) and about the same going in. If you cleared a whole weekend, and started on a friday evening, I think that would be plenty of time.

I'll help ya if I'm free when you are working on it, but can't make any promises I'll be free. On focaljet.com there are better tutorials then the crap one I just wrote, with pictures, so head over there. Also grab a hanes or chilton manual if you haven't. You'll need this is you get hung up on anything and for torque settings.

focinite · Mon Oct 22, 2007 12:53 am

pretty straight foreword. the svt trans is a little different in size than the mtx-75. youll be ok with out the motor brace. a tall jack stand and three shop rags rolled into a roll and duct taped to the jack stand placed inbetween the tans and oil pan( should be a flat spot there)should do the trick on the cheap. pull the batt out. remove any and all related stuff( recogmend a chiltons or comparable manule to walk you through). lift car. remove axles. unbolt trns from motor while a friend with a floor jack helps. lower trans r and r clutch. reverse to install.

KRYPTO · Mon Oct 22, 2007 5:33 pm

If you need help let me know, I'll have to do it on mine soon. So it would be nice to know what to expect.

mars · Tue Oct 23, 2007 8:27 am

thanx all, yea i'ma pick up the clutch and stuff from steve today... i'll let everyone know when i'ma start....

mars · Tue Oct 23, 2007 3:40 pm

alright i just picked up the clutch/flywheel from steve... now i'ma go and look for tools and pick up the engine crane from my cousins..... oh also i need to decide when i start the install.... maybe i'll wait til the car finally stops... hahaha LOL...

Tue Oct 23, 2007 4:17 pm

mars wrote: maybe i'll wait til the car finally stops... hahaha LOL...

Won't be long judging by the smell!!

let me know when you're woking on it, If I can help I certainly will.

I need the practice for mine

Tue Oct 23, 2007 4:21 pm

FORDSVTPARTS wrote:
mars wrote: maybe i'll wait til the car finally stops... hahaha LOL...
Won't be long judging by the smell!!

let me know when you're woking on it, If I can help I certainly will.

I need the practice for mine

It's nothing to be scared of. If Tony and I are free I'm sure we can both come, With both done clutches in these cars a good half dozen times between us haha.

This last time, I did my clutch in about 8 hours total, on my garage floor with hand tools. I did it in two 4 hours sittings (as I pulled it all apart before the new stuff had even shipped, haha).

It really isn't all that bad. Just pull shit out till the tranny falls out

focinite · Tue Oct 23, 2007 6:18 pm

Pappy wrote:
FORDSVTPARTS wrote:
mars wrote: maybe i'll wait til the car finally stops... hahaha LOL...
Won't be long judging by the smell!!

let me know when you're woking on it, If I can help I certainly will.

I need the practice for mine
It's nothing to be scared of. If Tony and I are free I'm sure we can both come, With both done clutches in these cars a good half dozen times between us haha.

This last time, I did my clutch in about 8 hours total, on my garage floor with hand tools. I did it in two 4 hours sittings (as I pulled it all apart before the new stuff had even shipped, haha).

It really isn't all that bad. Just pull shit out till the tranny falls out

pretty much

mars · Wed Oct 24, 2007 8:21 am

OK SO DO I NEED ANY SPECIAL TOOLS??? i'ma try to get everything ready.... my car isnt moving til i hit 5k on every gear now.... so i'm not sure if i'ma make it to the meet...

mars · Wed Oct 24, 2007 11:48 am

ok so i'm slowly collection tools for the install.... another question popped up... do i need to refill my tranny fluid or something after that install?? if so what fluid will i be needing to get...?

Wed Oct 24, 2007 12:25 pm

mars wrote:ok so i'm slowly collection tools for the install.... another question popped up... do i need to refill my tranny fluid or something after that install?? if so what fluid will i be needing to get...?

Yes you will. Post on FJ, I'm not sure if its the same type of fluid and amount for the getrag. For ours I run 2 quarts of GM syncromesh.

mars · Wed Oct 24, 2007 6:38 pm

DAMN the clutch went out... i'ma start the install this weekend starting on fri afternoon.....

KRYPTO · Wed Oct 24, 2007 9:08 pm

If you need some help, I'm down